Autor |
Nachricht |
Jan Kraak
|
Betreff des Beitrags: Dutch Tijgerhaai schaal 1:50 Verfasst: 10. September 2006, 19:53 |
|
|
De bau van ein keine Dutch "Tijgerhaai"wie Lothar Mentz im masstab 1:50 mit pressluft.
Zuletzt geändert von Jan Kraak am 27. Oktober 2006, 19:36, insgesamt 4-mal geändert.
|
|
Nach oben |
|
|
Jan Kraak
|
Betreff des Beitrags: tijgerhaai scale 1:50 update Verfasst: 27. Oktober 2006, 19:25 |
|
|
the sealing-rings are placed in the sub, also are the rudders ready to place in the sub.
|
|
Nach oben |
|
|
Lothar Mentz
|
Betreff des Beitrags: Verfasst: 28. Oktober 2006, 00:25 |
|
|
Hey Jan,
did You have her in the water to find out the center of gravity and the weight?
Lothar
|
|
Nach oben |
|
|
Jan Kraak
|
Betreff des Beitrags: Verfasst: 28. Oktober 2006, 15:24 |
|
|
no , next week the sub wants to make a bath in the aquarium.
I am now placing the ruders on the hull.
Then we shall see wtyh the weight is.
Now the sub is 10 kg inclusive the accu 12V-20Ah.
So I have 6 kg left to build further.
When he is to heavy, I can put less accu's, that's 1.6 kg
I believe that it comes right, it must be under the 16 kg.
|
|
Nach oben |
|
|
Jan Kraak
|
Betreff des Beitrags: Verfasst: 7. November 2006, 00:30 |
|
|
|
Nach oben |
|
|
Jan Kraak
|
Betreff des Beitrags: Verfasst: 10. Dezember 2006, 21:36 |
|
|
|
Nach oben |
|
|
Lothar Mentz
|
Betreff des Beitrags: Verfasst: 11. Dezember 2006, 12:33 |
|
|
|
Nach oben |
|
|
Jan Kraak
|
Betreff des Beitrags: Verfasst: 28. Dezember 2006, 22:51 |
|
|
The midsection has been made from one piece polyester with carbonfiber around a mould.
Dateianhänge: |
Dateikommentar: making a maintank of carbon
IMG_7085.JPG [ 70.97 KiB | 13745-mal betrachtet ]
|
Dateikommentar: maintank
IMG_7088.JPG [ 62.25 KiB | 13746-mal betrachtet ]
|
Zuletzt geändert von Jan Kraak am 14. Januar 2007, 21:05, insgesamt 1-mal geändert.
|
|
Nach oben |
|
|
Lothar Mentz
|
Betreff des Beitrags: Verfasst: 29. Dezember 2006, 01:04 |
|
|
|
Nach oben |
|
|
Jan Kraak
|
Betreff des Beitrags: Verfasst: 5. Januar 2007, 18:32 |
|
|
|
Nach oben |
|
|
Jan Kraak
|
Betreff des Beitrags: Verfasst: 13. Januar 2007, 18:38 |
|
|
The maintank with the periscoop room.
Dateianhänge: |
Dateikommentar: the three parts
IMG_7098.JPG [ 60.48 KiB | 13751-mal betrachtet ]
|
Dateikommentar: carbon maintank with a aluminium topplate.
IMG_7099.JPG [ 62.7 KiB | 13751-mal betrachtet ]
|
Zuletzt geändert von Jan Kraak am 14. Januar 2007, 20:59, insgesamt 2-mal geändert.
|
|
Nach oben |
|
|
Jan Kraak
|
Betreff des Beitrags: Verfasst: 17. Februar 2007, 15:03 |
|
|
|
Nach oben |
|
|
Lothar Mentz
|
Betreff des Beitrags: Verfasst: 24. Februar 2007, 15:15 |
|
|
Hi Jan,
the tanks are looking great! Very clean job!
You should try to wash away this green colour with "Aceton". This worked good for my pipes.
Lothar
|
|
Nach oben |
|
|
Jan Kraak
|
Betreff des Beitrags: Verfasst: 26. Februar 2007, 22:33 |
|
|
Black sunday in Den helder.
The space in the tijgerhaai scale 1:50 is to small to put there a pressure tank.
So i build one between the hull and the tube of copper pipe, but that is to heavy.
So then I must sail with fever battery's 12V/8A in place of 12V/16A
So conclusion to little space.
So next week we transform it into the old way with a deck in between, so i can use the stuff I already build and I can put 8 kg more into the sub.
So Lothar you are right, that its to small for a two tube hull.
But its get his air pressure en valves.
Pictures over two weeks.
Jan Kraak
Dateianhänge: |
Dateikommentar: airtank between the innerhull and the outher hull
IMG_7180.JPG [ 57.05 KiB | 13395-mal betrachtet ]
|
Dateikommentar: 1 liter of air
IMG_7181.JPG [ 50.86 KiB | 13395-mal betrachtet ]
|
Zuletzt geändert von Jan Kraak am 4. März 2007, 10:48, insgesamt 1-mal geändert.
|
|
Nach oben |
|
|
Lothar Mentz
|
Betreff des Beitrags: Verfasst: 26. Februar 2007, 23:42 |
|
|
Puuhhh... ooooh shi.... this is the worst case to make an expierance.....
Best regards and good luck at converting the boat!
Lothar
|
|
Nach oben |
|
|